线束加工常见名称中英文对照表
- 作者: 深华
- 来源: 缆仕特电子
- 日期 : 2024-04-07
在线束加工行业中，我们难免会接触到很多外资企业，他们的技术图纸或文档说明一般常见的一些名称都是英文描述，掌握一些基本的英文名称是很有必要的，下面给大家总结了一份《线束加工常见名称中英文对照表》。
| Raw material | 原材料 |
| Cover | 盖子 |
| Nut | 螺母 |
| Washer | 垫圈 |
| TPA/PLR | 锁止片 |
| Channel | 通道 |
| Fuse box | 保险盒 |
| Fuse | 保险 |
| Heat shrink tube | 热缩管 |
| Plug | 堵头 |
| Clip | 定位夹 |
| Strap | 扎带 |
| Wire | 电线 |
| Harness | 线束 |
| Sub Assy Wiring Harness | 半成品线 |
| Cable | 电缆 |
| Battery Cable | 电瓶线 |
| Bracket | 支架 |
| Corrugated Tube | 波纹管 |
| PVC Tube | PVC 管 |
| Tube | 管件 |
| ELECTRONICAL COMPONENT | 电子零件 |
| Junction Box | 接线盒 |
| Grommet | 护套 |
| Tape | 胶带 |
| Plastic | 塑料件 |
| Relay | 继电器 |
| Rubber | 橡胶件 |
| Seal | 密封塞 |
| Terminal | 端子 |
| Male Terminal | 公端子 |
| Female Terminal | 母端子 |
| Eyelet | 环端 |
| Fiber | 光纤 |
| Mat Seal | 密封垫 |
| Blind Cavity | 盲孔 |
| Cavity | 孔位 |
| Cavity No. | 孔位号 |
| Sleeve | 袖套 |
| PET Tape | PET 胶带 |
| Foam Tape | 泡沫胶带 |
| PVC Tape | PVC 胶带 |
| Textile Tape | 无纺布胶带 |
| Felt Tape | 毛毡胶带 |
| Glass Cloth Tape | 玻璃布胶带 |
| Connector | 连接器 |
| Conductor | 导体 |
| Waterproof | 防水 |
| Pusher | 推杆 |
| Diameter | 直径 |
| PUR Tube | PUR 管 |
| Gold Plated Terminal | 镀金端子 |
| Tin Plated Terminal | 镀锡端子 |
| Silver Plated Terminal | 镀银端子 |
| Multicore Wire | 多芯线 |
| Screening Wire | 屏蔽线 |
| Diode | 二极管 |
| 操作名称 | |
| Spot Tape | 点缠 |
| Full Tape | 全缠 |
| Spiral Tape | 间距缠 |
| Crossing Tape | 交叉缠 |
| Terminal Insert | 插端子 |
| Rework | 返工 |
| E-test | 电测 |
| Pre-assembly | 预装 |
| Tape Wound | 缠带 |
| Quality Inspection | 质检 |
| Process Check | 过程检查 |
| First Piece Inspection | 首检 |
| Last Piece Inspection | 末检 |
| Splice | 铰接 |
| Twist | 绞线 |
| Crimp | 压接 |
| Tube Heating | 烘管 |
| Assembly | 装配 |
| Wire Cutting | 切线 |
| Strip | 剥皮 |
| Weld | 焊接 |
| Ultrasonic | 超声波 |
| Ultrasonic Weld | 超声波焊接 |
| Tape Back | 回缠 |
| Package | 包装 |
| Scan | 扫描 |
| Torque | 扭矩 |
| Maintenance | 维修 |
| 线束名称 | |
| Rear Door Harness | 后门线束 |
| Front Door Harness | 前门线束 |
| Wheelhouse Harness | 机舱线束 |
| Body Harness | 车身线束 |
| Engine Harness | 发动机线束 |
| Roof Harness | 顶棚线束 |
| Epas Harness | 电动助力转向线束 |
| Front bumper Harness | 前保险杠线束 |
| Rear bumper Harness | 后保险杠线束 |
| Tailgate R Harness | 右尾门线束 |
| Tailgate L Harness | 左尾门线束 |
| Engine Ground Harness | 发动机接地线 |
| Underbody Harness | 底板线束 |
| IP Harness/ Instrument Panel Harness | 仪表板线束 |
| Starter Alternator | 启动发电机线束 |
| Main Battery Ground | 主蓄电池接地线 |
| Front Door Ground Illumination | 前门接地照明线束 |
| Rear Door Ground Illumination | 后门接地照明线束 |
| Rear Door Handle Adapter Harness | 后门把手转换线束 |
| 工装设备工具 | |
| Assembly board | 工装板/装配板 |
| Fork（tooling fork） | 工装叉 |
| OLTT(off line test table) | 电测台 |
| Inspection Table | 全检台/检测台 |
| Packaging Table | 包装台 |
| Scan Table | 扫描台 |
| Clip Board | 定位夹板/卡扣板 |
| Clip Fixture | 定位夹夹具/卡扣夹具 |
| Grommet Fixture | 护套夹具 |
| Connector Fixture | 连接器夹具 |
| Visual Aid | 目视辅助 |
| Rework Screwdriver | 返工/返工起子 |
| Strap Gun | 扎带枪 |
| Tube Assembling Tool/Tube insertion tool | 上管器 |
| Tube Cutter | 切管机 |
| Diagonal Pliers | 斜口钳 |
| Layout | 布局图 |
| Scanner(looks like gun) | 扫描枪 |
| Pressure guage | 压力检具 |
| (Push tool) | 推工具 |
| detection pin | 探针 |
| Module | ?？?/span> |
| Wire Cutter | 切线机 |
| Ultrasonic Welding Machine | 超声波焊接机 |
| Tube Heating Machine | 烘管机 |
| Stripper | 剥皮机 |
| Torque wrench | 扭力扳手 |
| 成品以及半成品 | |
| Branch | 分支 |
| Bundle | 捆，束 |
| Node | 节点 |
| Trunk | 主干 |
| Tolerance | 公差 |
| Orientation | 方向 |
| Fixture | 夹具 |
| Label | 标签 |
| Bar Code | 条形码 |
| Two-dimension Code | 二维码 |
| Error Proofing | 防差 |
| Sample | 样件 |
| Master Sample | 标准样件 |
| Product Sample | 产品样件 |
| Warehouse | 仓库 |
| Dimension | 尺寸 |
| Deviation | 偏差 |
| Bellmouth | 喇叭口 |
| Copper Strand | 铜丝 |
| Plate | 镀层 |
| Splice | 铰接点 |
| Twisted Circuit | 麻花线 |
| Twist Pitch | 绞距 |
| Parameter | 参数 |
| Compressing Rate | 压缩比 |
| Special Characteristics/SC | 特殊特性 |
| Critical Characteristics/CC | 重要特性 |
| Front Bellmouth | 前喇叭口 |
| Rear Bellmouth | 后喇叭口 |
| Window | 窗口/窗户 |
| Cut Off Tabs | 切断尾料 |
| Cross-Section | 横截面 |
| Strip Length | 剥皮长度 |
| Pull Force | 拉力 |
| Conductor | 导体 |
| Conductor Wing | 导体压接翼 |
| Conductor Crimp | 线芯压接 |
| Conductor Crimp Width/CCW | 线芯压接宽度 |
| Conductor Crimp Height/CCH | 线芯压接高度 |
| Insulation | 绝缘层 |
| Insulation Wing | 绝缘（层）压接翼 |
| Insulation Crimp | 绝缘层压接 |
| Insulation Crimp Width/ICW | 绝缘层压接宽度 |
| Insulation Crimp Height/ICH | 绝缘层压接高度 |
| 不良描述 | |
| Fracture | 断股 |
| low pull Force | 低拉力 |
| Scratch | 划伤-injury |
| Burnt | 烧伤 |
| Over Weld | 过烧 |
| Raw weld | 漏压 |
| Deform | 变形 |
| Oxidize | 氧化 |
| Discoloration | 退色/变色 |
| Cross Wires | 线交叉 |
| Open Circuit | 开路 |
| Short Circuit | 短路 |
| Rotate | 旋转 |
| Clip Rotate | 定位夹旋转 |
| Wild Strand | 散丝 |
| Missing Wires | 支路遗漏/漏线 |
| Damaged Wires | 支路破损 |
| Wrong Wires | 支路错误 |
| Cross Wire | 支路交叉 |
| Wrong Branch Dimension | 分支尺寸错误 |
| Wrong Branch Orientation | 分支方向错误 |
| Tight Circuit | 单根受力 |
| Wrong Branch | 分支错误 |
| Unseated Terminal | 端子未到位 |
| Damaged/Broken Terminal | 端子损坏/变形 |
| Faulty Terminal Crimping | 端子压接不良 |
| Missing Terminal | 端子缺失/遗漏 |
| Wrong Terminal | 端子用错/错误 |
| Unseated cover | 盖子未到位 |
| Wrong Connector | 连接器用错 |
| Damaged Connector | 连接器损坏 |
| Missing Connector | 连接器缺失/遗漏 |
| Damged TPA | 锁止片损坏 |
| Missing TPA | 锁止片遗漏 |
| Unseated TPA | 锁止片未到位 |
| Foreign Material in Connector | 连接器有异物 |
| Missing Seals/Plugs | 密封塞/堵头缺失/遗漏 |
| Wrong Seals/Plugs | 密封塞/堵头用错/错误 |
| Wrong Slide | 滑片用错/错误 |
| Pressed Terminal | 端子插入过度 |
| Wrong Terminal insertion orientation | 端子插入方向错误 |
| Wrong Ring-terminal assembly sequence | 环端组装顺序错误 |
| Missing Clip/Strap | 定位夹/扎带遗漏 |
| Wrong Clip/Strap Orientation | 定位夹/扎带方向错误 |
| Wrong Clip/Strap | 定位夹/扎带错误 |
| Wrong Clip Dimension | 定位夹尺寸错误 |
| Damged Clip/Strap | 定位夹/扎带损坏/坏了 |
| Wrong Tape | 胶带用错 |
| Tape Wound Defect | 胶带缠绕不良 |
| Missing Tape | 胶带遗漏 |
| Wrong Cross-wound tape | 胶带回缠错误 |
| Missing Cross-wound tape | 胶带回缠遗漏 |
| Damged Tape | 胶带损坏/坏了 |
| Wrong Channel/Bracket | 通道、支架用错 |
| Missing Channel/Bracket | 通道、支架遗漏 |
| Damged Channel/Bracket | 通道、支架损坏 |
| Wrong Channel Assembly | 通道安装/组装错误 |
| Wrong Grommet | 护套用错 |
| Missing Grommet | 护套遗漏 |
| Damaged Grommet | 护套损坏 |
| Wrong Grommet Assembly | 护套组装错误 |
| Wrong Tube | 管子用错 |
| Missing Tube | 管子遗漏 |
| Damaged Tube | 管子损坏 |
| Wrong Tube Assembly | 管件安装/组装错误 |
| Missing testing label | 电测/测试标签遗漏 |
| Wrong testing label | 电测标签错误 |
| Missing Label | 标签遗漏 |
| Missing Packaging | 包装遗漏 |
| Defective Splicing/Splicing Joint | 铰接点脱落 |
| Wrong Splicing Joint | 铰接点错误 |
| Faulty Welding | 焊接不良 |
| Missing Raw Material | 原材料遗漏 |
| Defective Raw Material | 原材料不良 |
| Unfasten Clip | 卡扣/定位夹扣合不良/松开 |
| Damged Fuse Box | 保险盒损坏 |
| Missing Fuse | 保险丝缺件 |
| Damged Fuse | 保险丝损坏 |
| Wrong Fuse | 保险丝用错 |
